Sealants, Potting Compounds

Epoxy cast resin SENO 4046

for general-purpose electronic and related applications. The material hardens after casting with especially low tension and inherent temperature. High insulating values with defined electrical data and VDE-tested. The quality of the hardened resin is recognized to be physiologically safe. Ideal for molding electronic circuits. This clear transparent cast resin can be tooled after hardening (sawing, drilling, milling). Also, it can be stained black easily and quickly with a special coloring paste.

Content: package with 1000 g resin plus 200 g hardener

Tensile strength: 500 to 800 kp/cm²

Pressure resistance: 800 to 1000 kp/cm²

Maximum continuous temperature: 90 °C (briefly 120 °C)

Hardening conditions:

- 15 to 30 hours at a room temperature of 20 °C

- 7 to 10 hours at 40 °C

- 2 to 4 hours at 70 °C

- 30 minutes at 100 °C

Signal word: Warning

Hazard statements:

• H315 Causes skin irritation
• H317 May cause an allergic skin reaction
• H319 Causes serious eye irritation
• H411 Toxic to aquatic life with long lasting effects

Precautionary statements:

• P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
• P273 Avoid release to the environment.
• P280 Wear protective gloves/protective clothing/eye protection/face protection/hearing protection/...
• P302+P352 IF ON SKIN: Wash with plenty of water/...
• P333+P313 If skin irritation or rash occurs: Get medical advice/attention.
• P391 Collect spillage.
• P501 Dispose of contents/container to ...

1C silicon adhesive and sealing compound, type Momentive formerly GE Bayer Silicones RTV

General-purpose adhesive and sealing compounds for electronic applications. Favorable properties, adhesion without primer on almost any substrate. The type designation RTV is the abbreviation for a typical compound property, namely the cross-linkage at room temperature.

Self-running, type RTV 118

Adhesive and sealing compound with good casting properties. Suitable for all dip/brush/spray applications. Fast curing at room temperature to form a tough and flexible rubber material.

Shore A hardness: 25

Tensile strength: 2.3 MPa

Density: 1.05 g/cm²

Elongation: 325%

Viscosity: 20000 mPa/s

Operating temperatures: +204 °C (briefly to +260 °C)

Note: the compound can act slightly corrosive (namely in combination with copper).

Type: RTV 118, clear, 82.8 ml tube

Supplemental Hazard
information:

• EUH210 Safety data sheet available on request

1C silicon adhesive and sealing compound, type Momentive vormals GE Bayer Silicones RTV

General-purpose adhesive and sealing compounds for electronic applications. Favorable properties, adhesion without primer on almost any substrate. The type designation RTV is the abbreviation for a typical compound property, namely the cross-linkage at room temperature.

Pasty, type RTV 103 Q

The pasty compound is applied and then cross-links at room temperature to form a strong silicon rubber. High dielectric values, moisture-resistant.

Shore A hardness: 30

Tensile strength: 2.8 MPa

Density: 1.05 g/cm²

Elongation: 450%

Operating temperatures: max.+200 °C (briefly to +260 °C)

Note: the compound can act slightly corrosive (namely in combination with copper)

Type: RTV 103 Q, black, 82.8 ml tube

Supplemental Hazard
information:

• EUH210 Safety data sheet available on request

1C silicon adhesive and sealing compound, type Momentive formerly GE Bayer Silicones RTV

General-purpose adhesive and sealing compounds for electronic applications. Favorable properties, adhesion without primer on almost any substrate. The type designation RTV is the abbreviation for a typical compound property, namely the cross-linkage at room temperature.

Pasty, type RTV 108

The pasty compound is applied and then cross-links at room temperature to form a strong silicon rubber. High dielectric values, moisture-resistant.

Shore A hardness: 30

Tensile strength: 2.8 MPa

Density: 1.05 g/cm²

Elongation: 450%

Operating temperatures: max.+200 °C (briefly to +260 °C)

Note: the compound can act slightly corrosive (namely in combination with copper)

Type: RTV 108, clear, 82.8 ml tube

Supplemental Hazard
information:

• EUH210 Safety data sheet available on request

1C silicon adhesive and sealing compounds, type Momentive vormals GE Bayer Silicones RTV.

General-purpose adhesive and sealing compounds for electronic applications. Favorable properties, adhesion without primer on almost any substrate. The type designation RTV is the abbreviation for a typical compound property, namely the cross-linkage at room temperature.

Self-running, type RTV 116.

High temperature-resistant, chemical-proof, adhesion without primer on almost all substrates, good electrical insulation properties; Shore A hardness: 20. Tensile strength: 2.5 MPa. Elongation: 350 %. Note: the compound can act slightly corrosive (namely in combination with copper). Operating temperatures: max. +260 °C (briefly to +315 °C).

Type: RTV 116, red, 82.8 ml tube

Signal word: Warning

Hazard statements:

• H315 Causes skin irritation

Precautionary statements:

• P264 Wash ... thoroughly after handling.
• P280 Wear protective gloves/protective clothing/eye protection/face protection/hearing protection/...
• P332+P313 If skin irritation occurs: Get medical advice/attention.
• P362+P364 Take off contaminated clothing and wash it before reuse.

RTV Silicon, 3110.310.KT.E500, Ergo

RTV Silicone is low odor and non-corrosive because the by-products of cure are chemically neutral. Also is an adhesive that achieves optimum seals, protection and adhesion to a wide variety of materials. It is typically used in situations that require bonds or seals to surfaces in heating or cooling devices, or in applications where electronic components require protection from external forces (vibration, impact, moisture and chemicals).

The product is characterized by its high temperature resistance, mechanical strength and resistance to vibration as well as its excellent weather and chemical resistance.

Applications

• Sealing parts in household appliances
• Seals in electronic components
• Seals in automotive applications
• Sealing joints or transitions

Supplemental Hazard
information:

• EUH210 Safety data sheet available on request

Silicone Sealant, 3120.200.DD.E500, Ergo

Neutral cure one-component RTV silicone formulated for use in a wide range of industrial applications. Silicone red is low odor and non-corrosive because the by-products of cure are chemically neutral.

The product is characterized by its resistance to extreme heat exposure, mechanical strength and resistance to vibration as well as its excellent weather and chemical resistance.

Applications

• Seals, protection and adhesion to a wide variety of materials
• Bonding and sealing parts in household appliances (e.g. ovens and ceramic hobs)
• Seals in electronic components (e.g. accumulators)
• Seals in automotive applications

Supplemental Hazard
information:

• EUH210 Safety data sheet available on request

Polyurethane cast resin, PURe Durchsicht ST 43, crystal-clear

2-component system, for molding electronic components, LED lights and for general applications in optoelectronic systems, high transparency, high resistance against weathering and UV radiation.

Mixing ratio resin/hardener: 100 : 60

Pot time: 30 to 40 min. Curing time 16 to 30 h

Final hardening: 10 to 14 days

Viscosity (mixed): 600 to 750 PAs

Thermal conductivity: 0.2 W/mK

Insulation material class: B

Application temperatures: - 40 to +130 °C

Signal word: Warning

Hazard statements:

• H319 Causes serious eye irritation
• H317 May cause an allergic skin reaction
• H332 Harmful if inhaled
• H335 May cause respiratory irritation

Precautionary statements:

• P264 Wash ... thoroughly after handling.
• P280 Wear protective gloves/protective clothing/eye protection/face protection/hearing protection/...
• P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P337+P313 If eye irritation persists: Get medical advice/attention.
• P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
• P271 Use only outdoors or in a well-ventilated area.
• P272 Contaminated work clothing should not be allowed out of the workplace.
• P302+P352 IF ON SKIN: Wash with plenty of water/...
• P333+P313 If skin irritation or rash occurs: Get medical advice/attention.
• P362+P364 Take off contaminated clothing and wash it before reuse.
• P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.
• P312 Call a POISON CENTRE/doctor/… if you feel unwell.
• P403+P233 Store in a well-ventilated place. Keep container tightly closed.
• P405 Store locked up.
• P501 Dispose of contents/container to ...

1C silicon rubber, type Wacker Elastosil A33

Excellent adhesive properties. Tube dispenser. Immediately ready for use. Vulcanizing and hardening time depends on humidity and temperature. By contrast to other silicon rubber sealing compounds, Elastosil does not attack alkaline substances. No formation of rust on ferrous metals as noticeable with other hardening systems.

Shore hardness A: 25

Elongation at fracture: 350 %

Tensile strength: 2.5 N/mm²

Tear resistance: 7.0 N/mm

Thermal conductivity: 0.3 W/mK

Signal word: Danger

Hazard statements:

• H315 Causes skin irritation
• H318 Causes serious eye damage.

Precautionary statements:

• P280 Wear protective gloves/protective clothing/eye protection/face protection/hearing protection/...
• P302+P352 IF ON SKIN: Wash with plenty of water/...
• P332+P313 If skin irritation occurs: Get medical advice/attention.
• P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P310 Immediately call a POISON CENTER/doctor/…
• P501 Dispose of contents/container to ...

Epoxy cast resin SENO 4046

for general-purpose electronic and related applications. The material hardens after casting with especially low tension and inherent temperature. High insulating values with defined electrical data and VDE-tested. The quality of the hardened resin is recognized to be physiologically safe. Ideal for molding electronic circuits. This clear transparent cast resin can be tooled after hardening (sawing, drilling, milling). Also, it can be stained black easily and quickly with a special coloring paste.

Content: package with 100 g resin plus 20 g hardener

Tensile strength: 500 to 800 kp/cm²

Pressure resistance: 800 to 1000 kp/cm²

Maximum continuous temperature: 90 °C (briefly 120 °C)

Hardening conditions:

- 15 to 30 hours at a room temperature of 20 °C

- 7 to 10 hours at 40 °C

- 2 to 4 hours at 70 °C

- 30 minutes at 100 °C

Signal word: Warning

Hazard statements:

• H315 Causes skin irritation
• H317 May cause an allergic skin reaction
• H319 Causes serious eye irritation
• H411 Toxic to aquatic life with long lasting effects

Precautionary statements:

• P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
• P273 Avoid release to the environment.
• P280 Wear protective gloves/protective clothing/eye protection/face protection/hearing protection/...
• P302+P352 IF ON SKIN: Wash with plenty of water/...
• P333+P313 If skin irritation or rash occurs: Get medical advice/attention.
• P391 Collect spillage.
• P501 Dispose of contents/container to ...

Polyurethane cast resin, type PURe Isolation ST 33, black

2-component system, contains non-abrasive mineral fillers, free of halogenated flame retardants, very low viscosity. Excellent properties in terms of electrical insulation, physical properties, and resistance against chemicals in hardened state.

Dielectric strength: 28 kV/mm

Specific forward resistance: 5.8 x 10^14 ohm/cm

Surface resistance: 1.3 x 10^16 ohm

Mixing ratio resin/hardener: 2 : 1

Pot time: 20 to 30 min.

Curing time: 16 to 30 h

Final hardened state: 10 to 14 days

Viscosity (mixed): 500 to 600 PAs

Shore hardness: D 50 to 55 (ISO 868, DIN 53505)

Thermal conductivity: 0.3 W/mK

Application temperatures: - 20 to +130 °C

Signal word: Danger

Hazard statements:

• H302 Harmful if swallowed
• H361fd Suspected of damaging fertility. Suspected of damaging the unborn child.
• H315 Causes skin irritation
• H317 May cause an allergic skin reaction
• H319 Causes serious eye irritation
• H332 Harmful if inhaled
• H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled
• H335 May cause respiratory irritation
• H351 Suspected of causing cancer
• H373 May cause damage to organs

Precautionary statements:

• P501 Dispose of contents/container to ...
• P201 Obtain special instructions before use.
• P202 Do not handle until all safety precautions have been read and understood.
• P270 Do not eat, drink or smoke when using this product.
• P280 Wear protective gloves/protective clothing/eye protection/face protection/hearing protection/...
• P301+P312 IF SWALLOWED: Call a POISON CENTRE/doctor/… if you feel unwell.
• P330 Rinse mouth.
• P308+P313 IF exposed or concerned: Get medical advice/ attention.
• P405 Store locked up.
• P264 Wash ... thoroughly after handling.
• P260 Do not breathe dust/fume/gas/mist/vapours/spray.
• P271 Use only outdoors or in a well-ventilated area.
• P272 Contaminated work clothing should not be allowed out of the workplace.
• P284 [In case of inadequate ventilation] wear respiratory protection.
• P302+P352 IF ON SKIN: Wash with plenty of water/...
• P362+P364 Take off contaminated clothing and wash it before reuse.
• P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.
• P342+P311 If experiencing respiratory symptoms: Call a POISON CENTER/doctor/...
• P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P337+P313 If eye irritation persists: Get medical advice/attention.
• P403+P233 Store in a well-ventilated place. Keep container tightly closed.

WEICON Repair Stick Stahl

- fast cure

- steel-filled

- NSF approval, can be used in drinking water aereas

It is particularly suited for the fast and high-strength repair and bonding of metal parts and for the patching and sealing of cracks, holes, and leaks in machine parts, tanks and pipelines, containers, pumps and housings, balcony railings, banisters, and torn-out threads.

The WEICON Repair Stick Steel can be used in machine and system construction, in tank construction and apparatus engineering, in the foods, cosmetic and pharmaceutical industries and in many other applications.

Thermal resistance: - 50 to +120 °C

Weight: 57 g

Signal word: Warning

Hazard statements:

• H315 Causes skin irritation
• H317 May cause an allergic skin reaction
• H319 Causes serious eye irritation
• H412 Harmful to aquatic life with long lasting effects

Precautionary statements:

• P280 Wear protective gloves/protective clothing/eye protection/face protection/hearing protection/...
• P273 Avoid release to the environment.
• P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
• P264 Wash ... thoroughly after handling.
• P362+P364 Take off contaminated clothing and wash it before reuse.
• P302+P352 IF ON SKIN: Wash with plenty of water/...
• P333+P313 If skin irritation or rash occurs: Get medical advice/attention.
• P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P337+P313 If eye irritation persists: Get medical advice/attention.
• P501 Dispose of contents/container to ...

Supplemental Hazard
information:

• EUH208 Contains (name of sensitising substance). May produce an allergic reaction.

Polyurethane cast resin, copaltec PURer Flammschutz BR 51, blue

2-component system with self-extinguishing properties in hardened state, contains non-abrasive mineral fillers. Its increased thermal conductivity has a positive cooling effect on the component. Free of halogenated flame retardants. Flexible in hardened state.

Inflammability class: UL94 V-0 (with 4.0 mm layer thickness)

Dielectric strength: 25 kV/mm

Specific forward resistance: 10^15 ohm/cm

Surface resistance: 10^16 ohm

Mixing ratio resin/hardener: 100 : 15

Pot time: 100 to 120 minutes

Curing time: 16 to 30 h

Final hardened state: 10 to 14 days

Viscosity (mixed): 2000 to 2200 PAs

Thermal conductivity: 0.8 W/mK

Insulation material class: B

Application temperatures: - 40 to +130 °C

Signal word: Danger

Hazard statements:

• H315 Causes skin irritation
• H317 May cause an allergic skin reaction
• H319 Causes serious eye irritation
• H332 Harmful if inhaled
• H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled
• H335 May cause respiratory irritation
• H351 Suspected of causing cancer
• H373 May cause damage to organs

Precautionary statements:

• P202 Do not handle until all safety precautions have been read and understood.
• P260 Do not breathe dust/fume/gas/mist/vapours/spray.
• P264 Wash ... thoroughly after handling.
• P271 Use only outdoors or in a well-ventilated area.
• P272 Contaminated work clothing should not be allowed out of the workplace.
• P280 Wear protective gloves/protective clothing/eye protection/face protection/hearing protection/...
• P284 [In case of inadequate ventilation] wear respiratory protection.
• P302+P352 IF ON SKIN: Wash with plenty of water/...
• P362+P364 Take off contaminated clothing and wash it before reuse.
• P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.
• P342+P311 If experiencing respiratory symptoms: Call a POISON CENTER/doctor/...
• P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P337+P313 If eye irritation persists: Get medical advice/attention.
• P308+P313 IF exposed or concerned: Get medical advice/ attention.
• P403+P233 Store in a well-ventilated place. Keep container tightly closed.
• P405 Store locked up.
• P501 Dispose of contents/container to ...

1C silicon adhesive and sealing compound, type Momentive vormals GE Bayer Silicones RTV

General-purpose adhesive and sealing compounds for electronic applications. Favorable properties, adhesion without primer on almost any substrate. The type designation RTV is the abbreviation for a typical compound property, namely the cross-linkage at room temperature.

Pasty, type RTV 102

The pasty compound is applied and then cross-links at room temperature to form a strong silicon rubber. High dielectric values, moisture-resistant.

Shore A hardness: 30

Tensile strength: 2.8 MPa

Density: 1.05 g/cm²

Elongation: 450%

Operating temperatures: max.+200 °C (briefly to +260 °C)

Note: the compound can act slightly corrosive (namely in combination with copper)

Type: RTV 102, white, 82.8 ml tube

Supplemental Hazard
information:

• EUH210 Safety data sheet available on request

WEICON Repair Stick Stahl

- fast cure

- steel-filled

- NSF approval, can be used in drinking water aereas

It is particularly suited for the fast and high-strength repair and bonding of metal parts and for the patching and sealing of cracks, holes, and leaks in machine parts, tanks and pipelines, containers, pumps and housings, balcony railings, banisters, and torn-out threads.

The WEICON Repair Stick Steel can be used in machine and system construction, in tank construction and apparatus engineering, in the foods, cosmetic and pharmaceutical industries and in many other applications.

Thermal resistance: - 50 to +120 °C

Weight: 115 g

Signal word: Warning

Hazard statements:

• H315 Causes skin irritation
• H317 May cause an allergic skin reaction
• H319 Causes serious eye irritation
• H412 Harmful to aquatic life with long lasting effects

Precautionary statements:

• P280 Wear protective gloves/protective clothing/eye protection/face protection/hearing protection/...
• P273 Avoid release to the environment.
• P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
• P264 Wash ... thoroughly after handling.
• P362+P364 Take off contaminated clothing and wash it before reuse.
• P302+P352 IF ON SKIN: Wash with plenty of water/...
• P333+P313 If skin irritation or rash occurs: Get medical advice/attention.
• P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P337+P313 If eye irritation persists: Get medical advice/attention.
• P501 Dispose of contents/container to ...

Supplemental Hazard
information:

• EUH208 Contains (name of sensitising substance). May produce an allergic reaction.